Eltek Rectiverter Power Core 110 VDC 18 kVA 1ph or 3ph Up to 18Kva
AC & 14.4kw 110Vdc output (Part No. CIOR1207.1xxx)
Applications :
The rectiverter 2U 19inch integrated system can be used as a stand
alone system with bulk AC &DC output in industiral applications
where a 230 /115Vac and 110Vdc back up is needed.
The total output power for both AC and DC is limited to a total
8KW, AC and DC output limits can be set according to the connected
load, where the limitation for AC load is set to max 6kVA and for
DC load to max 4KW ,8KW.
As additional options, the measuring and signaling can be widely
extended with the I/Q monitor or Flexi monitor CAN nodes.
TELECOM-MOBILE/WIRELESS
· LTE/4G/WiMAX
· Distributed antenna system
· Broadband
· Radio base stations/cell sites
POWER UTILITIES
· Low & High voltage switchgear
· Transformer & SUB stations
· Control & protection
· SCADA system
RAILWAY & METRO INFRASTRUCTURE
· Control & protection
· Signaling
Key Features :
- l Compact design and simple installation
- l Single phase 230 or 115VAC input and output
- l 48Vdc input and output
- l Up to 4 rectiverter modules
- l 8KW total AC+DC output
- l Max 6kVA AC output
- l Max 4KW/ 8KW DC output
- l 1 or 2 pole AC distribution options
- l 1 Pole DC distribution option
- l Built in transfer technology
Techinical Data:
|
| Models / ordering information 24 kW, 230 V 1ph | 24 kW, 400 V 3ph |
| Product family CIOR1207.1xxx |
| AC OUTPUT DATA |
| Voltage (default) / (adjustable range)1) 230 VAC / 200 - 240 VAC
400 VAC 3 phase (Y) / 346-415 VAC |
| Frequency (default inverter mode) 50Hz (adaptive) |
| Frequency (set-able inverter mode) 50Hz, 60Hz or last synced
50/60Hz (adaptive) |
| Power maximum (continuous / overload (<15s) ) 14,4 kW (18 kVA) /
24 kVA |
| Current maximum/phase (continuous / overload (<15s) ) 78ARMS /
104,4ARMS | 26ARMS / 34,8ARMS |
| Current (maximum) Quick trip/phase (20ms) 384 A (6 x nominal) | 128 A (6 x nominal) |
| Hold up (Voltage dips) (before switching to battery) > 5 ms @
14,4 kW load |
| THD < 1.5 % at resistive load |
| Output features Fuse in L and N, Hot pluggable |
| DC OUTPUT DATA |
| Voltage (default) / (adjustable range) 122,5 VDC / 97 - 145 VDC |
| Power (maximum @nominal input) 14,4 kW 2) |
| Current (maximum @VOUT ≤ 108 VDC) 133 A 2) |
| Hold up time, maximum output power >10ms; VOUT > 41 VDC |
| Output features Short circuit proof, Over voltage Shutdown, Bulk DC
output connection to M8 bolt |
| INPUT DATA |
| AC Mains Input Voltage(3 phase Y) 185 - 275 VAC,(single phase) 320
- 475 VAC ,(3 phase Y) |
| AC Current/phase(at nominal output voltage) (depending on module
type) 84-144 ARMS 4) | 28-48 ARMS 4) |
| Frequency (default: sync range) 47-53 & 57-63 Hz |
| Frequency (set-able: sync range) 47-53 Hz, 57-63 Hz or both
(adaptive) |
| Power Factor / THD > 0.99 at 50% load or more / < 3.5% |
| DC Voltage nominal / extended range (no overload)3) 102 - 145 VDC / 90 - 102 VDC |
| DC Current (maximum) 150 A / 216 A during overload (15s) |
Fuse in L and N, Hot pluggable, Varistor, Hot pluggable Input features AC input individual screw terminals 10 mm2 for
L1,L2,L3, or L1,L1,L1 + N & PE Bulk DC input connection to M8 bolt Bulk DC battery connection to M8 bolt |
| OPTIONS |
| Control and monitoring (see Smartpack2 datasheet) Smartpack2,
including industrial basic & I/O monitor type 2 |
| 1 pole AC distribution (L connection directly on MCB) 1-18 pc,
2-20A, C or B characteristics | 1-18 pc, 2-20A, C or B characteristics |
| 3 pole AC distribution (L1-L3 connection directly on MCB) - | 1-6 pc, 2-20A, C or B characteristics |
| OTHER SPECIFICATION |
| Efficiency >96% (mains mode (AC/AC and AC/DC)), >94%
(inverter mode (DC/AC)) |
| Manual bypass switch 63 A (make before break) |
| Protection Class IP 20 |
| Operating temperature -40 to +55°C (-40 to +131°F), humidity 5 -
95% RH non-condensing |
| Storage temperature -40 to +85°C (-40 to +185°F), humidity 0 - 99%
RH non-condensing |
| Dimensions[WxDxH] / Weight 482 x 432 x 311mm (7U) (19 x 17 x 12,3”)
/ 27kg (60 lbs) |
| DESIGN STANDARDS |
| Electrical safety EN 60950-1, EN 62040-1 UPS safety |
EMC ETSI EN 300 386 V.1.6.1, FCC CFR 47 Part 15 EN 61000-6-1 /-2/-3/-4, EN62040-2 |
ETSI EN 300 019: 2-1 (Class 1.2), 2-2 (Class 2.3) Environment Normal operating conditions to be as per IEC/EN
62040-3:2011 clause 4.1 RoHS (2011/65/EU) and WEEE (2002/96/EC)
compliant |
1) Output voltage ranges configured in factory and have individual
keying in top chassis 2) AC load has priority. Maximum available DC output power and current is dependent on 3) 90-102 VDC: reduced performance - no power boost and increased
voltage THD on AC output. instant AC load and AC input voltage; i.e
maximum 9600W/87 A at full AC power and nominal input for 230VAC. 4) If DC voltage is pulled below 97V the input current may increase
above this level |
Related Products:
Solutions
We provide a complete solutions including site survey, propose
professional plan according to customer’s request ,technical
support, and maintenance service for Telecommunication Companies in
and out of China. We have a competent team and a network of trusted
Partners around the world.
FAQ :
1. How do you control the quality?
A:All products before the shipment are simulated usage scenarios,
load and full load and current sharing test to ensure the quality
of the product.
2. What is your minimum order quantity?
A:There is no minimum order quantity, and one can also be done. The
only difference is the price and schedule.
3. Can you introduce your company?
A:I am very honored. I will send you the company’s introduction
document later to give you a more comprehensive and direct
introduction to our company’s information.
4. What are the advantages of your company?
A:Adequate inventory, and supply guarantee for the subsequent
renewal of supply, flexible provided according to different to
different needs of customers, providing different solutions.
5. Can i send samples?Report it to me along with the price?
A:You can send samples, the samples are subject to large pride, and
the freight needs to be borne by you.
6. How do your company deal with the problem on quality?
A:Our company has been doing this industry for almost 10 years. It
has already had a certain reputation. We will carefully analyze it.
If it is indeed our quality problem, you can rest assured that it
will do things according to the contract agreement and will never
let you have any after the worries, our service team will be happy
to serve you.
7 What about the quality ?
A:100% original with new package. we will test each item before
posted to make sure each item with good quality.
8 How many months for guarantee ?
A: 1 year quality guarantee
9 How to deal with any inferior -quality goods ?
A: Goods can be post by with our charge of post fee for any bad
quality products within guarantee time.
