Eltek Rectiverter Integrated 2U, 48VDC 6kVA 1ph systems with
Smartpack 2 Touch and basic (part No.CIOR0402)
Applications :
The rectiverter 2U 19inch integrated system can be used as a stand
alone system with bulk AC &DC output in industiral applications
where a 230 /115Vac and 110Vdc back up is needed.
The total output power for both AC and DC is limited to a total
8KW, AC and DC output limits can be set according to the connected
load, where the limitation for AC load is set to max 6kVA and for
DC load to max 4KW ,8KW.
As additional options, the measuring and signaling can be widely
extended with the I/Q monitor or Flexi monitor CAN nodes.
TELECOM-MOBILE/WIRELESS
· LTE/4G/WiMAX
· Distributed antenna system
· Broadband
· Radio base stations/cell sites
POWER UTILITIES
· Low & High voltage switchgear
· Transformer & SUB stations
· Control & protection
· SCADA system
RAILWAY & METRO INFRASTRUCTURE
· Control & protection
· Signaling
Key Features :
l Compact design and simple installation
l Single phase 230 or 115VAC input and output
l 48Vdc input and output
l Up to 4 rectiverter modules
l 8KW total AC+DC output
l Max 6kVA AC output
l Max 4KW/ 8KW DC output
l 1 or 2 pole AC distribution options
l 1 Pole DC distribution option
l Built in transfer technology
Techinical Data:
|
| Models | 8 kW, 230 VAC | 4 kW, 115 VAC |
| Product family | CIOR0402.1xxx | CIOR0402.1xxx |
| AC OUTPUT DATA |
| Voltage (default) / (adjustable range) 1) | 230 VAC / 200-240 VAC | 115 VAC / 100-127 VAC |
| Frequency (inverter mode – default) | 50 Hz (adaptive) | 60 Hz (adaptive) |
| Frequency (inverter mode – settable) | 50 Hz, 60 Hz or last synced 50 / 60 Hz (adaptive) |
| Power maximum (continuous / overload <15s) | 4800 W (6000 VA) / 8000 VA | 2400 W (3000 VA) / 4000 VA |
| Current maximum (continuous / overload <15s) | 26 ARMS / 34,8 ARMS |
| Current (maximum) quick trip (20ms) | 128 A (6 x nominal) |
| Hold up (Voltage dips) (before switching to battery) | 5 ms | 5 ms |
| THD | < 1,5 % at resistive load |
| Protection | Fuse in L, Hot pluggable, Varistor |
| DC OUTPUT DATA |
| Voltage (default) / (adjustable range) | 53,5 VDC / 43-58 VDC |
| Power (maximum @nominal input) | 4800 W 2) | 2400 W 2) |
| Current (maximum @VOUT ≤ 48 VDC) | 100 A 2) | 50 A 2) |
| Current sharing (10 - 100% load) | ±5 % of maximum current from 10 to 100 % load |
| Protection | Short circuit proof, Over voltage shutdown, Reversed polarity and
Fuse |
| INPUT DATA |
| AC Mains Input Voltage (range / LV disconnect) | 185-275 VAC / 170 VAC | 95-140 VAC / 85 VAC |
| AC Current (maximum - depends on module type) | 32,8-46 ARMS 3) | 36,8-45,2 ARMS 3) |
| Frequency (default: sync range) | 47-53 & 57-63 Hz | 57-63 & 47-53 Hz |
| Frequency (settable: sync range) | 47-53 Hz, 57-63 Hz or both (adaptive) |
| Power Factor / THD | > 0,99 at 70% load or more / < 3,5 % |
| DC Voltage nominal / extended range 4) | 45-58 VDC / 40-45 VDC |
| DC Current (maximum) | 128 A / 180 A during overload (15 s) | 64 A / 90 A during overload (15 s) |
| Input features | Fuse in L and N, Hot pluggable, Varistor AC input individual screw terminals 4 mm2 for L, N & PE (4x single phase) |
| OPTIONS |
| Control and Monitoring (master unit) | Smartpack2 Touch |
| Control and Monitoring (basic unit) | Smartpack2 Basic |
| Controller CAN node | I/O Monitor T2 |
| AC distribution | AC output individual screw terminals 10 mm2 for L, N & PE (1x single phase) |
| DC distribution | DC bulk connection on 2x M6 bolt |
| OTHER SPECIFICATION |
| Efficiency | > 96 % (mains mode), > 94 % (inverter mode) | > 92 % (mains mode), > 91 % (inverter mode) |
| Operating temperature | -40 to +55 °C (-40 to +131 °F), humidity 5-95 % RH non-condensing |
| Storage temperature | -40 to +85 °C (-40 to +185 °F), humidity 0-99 % RH non-condensing |
| Dimensions [W x D x H] | 482 x 400 x 89 mm (2U) (19 x 15,7 x 3,5 inch) | |
| Weight | 9,4 kg (20,7 lbs) | |
| DESIGN STANDARDS |
| Electrical safety | EN 60950-1, EN 62040-1 UPS safety | |
EMC | ETSI EN 300 386 V2.1.1, FCC CFR 47 Part 15 EN 62040-2 EN 61000-6-1/-2/-3/-4/-5 | |
Environment | ETSI EN 300 019: 2-1 (Class 1.2), 2-2 (Class 2.3) & 2-3 (Class 3.2) Normal operating conditions as per IEC 62040-3:2011 clause 4.2.
Other operating conditions as per IEC 62040-3:2011 clause 4.3, must
be advised RoHS 3 (2015/863/EU) and WEEE (2008/98/EC) compliant |
1) Output voltage ranges configured in factory and have individual
keying in top chassis 3) If DC port is overloaded pulling the voltage below 43 V the
input current may increase above this level. | 2) AC load has priority. Maximum available DC output power and current is dependent on instant AC load and AC
input voltage; i.e. maximum 3200 W / 66,4 A at full AC power and nominal input for
230 VAC. 4) Reduced performance - no over load support, and for 200-240 VAC
output THD will increased and maximum output power de- rates (to
970 W for 230 VAC @ 40 VDC) |
Related Products:
Solutions
We provide a complete solutions including site survey, propose
professional plan according to customer’s request ,technical
support, and maintenance service for Telecommunication Companies in
and out of China. We have a competent team and a network of trusted
Partners around the world.
FAQ :
1. How do you control the quality?
A:All products before the shipment are simulated usage scenarios,
load and full load and current sharing test to ensure the quality
of the product.
2. What is your minimum order quantity?
A:There is no minimum order quantity, and one can also be done. The
only difference is the price and schedule.
3. Can you introduce your company?
A:I am very honored. I will send you the company’s introduction
document later to give you a more comprehensive and direct
introduction to our company’s information.
4. What are the advantages of your company?
A:Adequate inventory, and supply guarantee for the subsequent
renewal of supply, flexible provided according to different to
different needs of customers, providing different solutions.
5. Can i send samples?Report it to me along with the price?
A:You can send samples, the samples are subject to large pride, and
the freight needs to be borne by you.
6. How do your company deal with the problem on quality?
A:Our company has been doing this industry for almost 10 years. It
has already had a certain reputation. We will carefully analyze it.
If it is indeed our quality problem, you can rest assured that it
will do things according to the contract agreement and will never
let you have any after the worries, our service team will be happy
to serve you.
7 What about the quality ?
A:100% original with new package. we will test each item before
posted to make sure each item with good quality.
8 How many months for guarantee ?
A: 1 year quality guarantee
9 How to deal with any inferior -quality goods ?
A: Goods can be post by with our charge of post fee for any bad
quality products within guarantee time.
